Pinter Xerox Phaser 750 error codes list

Error 01:

• Remove and re-install the black Toner Cartridge, then turn the printer off and on.


• Replace the black Toner Cartridge, then turn the printer off and on.

Error 02:

• Remove and re-install the cyan Toner Cartridge, then turn the printer off and on.


• Replace the cyan Toner Cartridge, then turn the printer off and on.

Error 03:

• Remove and re-install the magenta Toner Cartridge, then turn the printer off and on.


• Replace the magenta Toner Cartridge, then turn the printer off and on.

Error 04:

• Remove and re-install the yellow Toner Cartridge, then turn the printer off and on.


• Replace the yellow Toner Cartridge, then turn the printer off and on.

Error 05, 10, 11, 12, and 13:

• Turn the printer power off, then on.

Error 20:

• Remove and re-install the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.


• Remove and re-install the Main Charge Grid. Turn the printer off, then on.


• Remove and re-install the Transfer Kit. Turn the printer off, then on.


• Remove and re-install each of the Toner Cartridges. Turn the printer off, then on.


• Replace the Main Charge Grid. Turn the printer off, then on.


• Replace the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.


• Replace the Transfer Kit. Turn the printer off, then on.


• Replace the Toner Cartridges. Turn the printer off, then on.

Error 21, 22, 30, and 32:

• Remove and re-install the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.


• Replace the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.


• If a problem persists for Error 30, clean the sensor. See Cleaning Phaser 750 Printers.

Error 33:

• Check for jammed paper throughout the paper path (especially in paper feeder).


• Remove and re-install the paper feeder and Transfer Kit. Turn the printer off, then on.

Error 40, 41, 42, and 43:

• Check for jammed paper in the Fuser. Re-install the Fuser. Turn the printer off, then on.


• Make sure that you have the correct Fuser for your local printer power supply:


• 110-Volt Fuser Part Number 016-1839-00


• 220-Volt Fuser Part Number 016-1840-00


• Replace the Fuser. Turn the printer off, then on.

Error 50, 51:

• Turn the printer off, then on.

Error 52:

• Remove the Duplex Unit (if installed).


• Check for paper under the Upper Tray.


• Turn power off, then on.

Error 53:

• Open left door and remove any jammed media.


• Tun the printer off, then on.

Error 60:

• Remove the media from the Multi-Purpose Tray. Turn the printer off, then on.


• Reinstall the media. Make sure you do not overfill the tray.

Error 61:

• Remove and re-install each Toner Cartridge. Turn the printer off, then on.


• Replace each Toner Cartridge. Turn the printer off, then on.

Error 62:

• Check for jammed paper throughout the paper path (especially in the paper feeder and Fuser).


• Remove and re-install the Fuser. Turn the printer off, then on.


• Slide out and re-insert the paper feeder. Turn the printer off, then on.


• Replace the Fuser. Turn the printer off, then on.

Error 63:

• Remove and re-install the Imaging Unit. Turn the printer off, then on.


• Replace the Imaging Unit. Turn the printer off, then on.

Error 70, 71, and 72:

• Turn the printer off, then on.

Error 73:

• Remove and re-install the Imaging Unit. Turn the printer off, then on.


• Replace the Imaging Unit. Turn the printer off, then on.

Error 74:

• Remove and re-install the Fuser. Turn the printer off, then on.


• Replace the Fuser. Turn the printer off, then on.

Error 80, 81, 82, 83, and 84:

• Make sure that all four toner cartridges are installed in the printer.


• Turn the printer off, then on.

Error 01p through Error 47p:

• Make sure that installed memory DIMM(s) are compatible with printer's image processor board and that they are installed in the proper slot(s).

Posted in: Xerox phaser